Static port location

Description of your first forum.
Post Reply
jchisolm
Posts: 111
Joined: Tue Jun 17, 2014 9:56 pm

Static port location

Post by jchisolm »

CT tail express
I'm not using a Piper style blade pitot/static so I need a separate static port. Any suggestions on where to locate the static port?
I read a post in the old forum where they put it a few inches forward of the sta 162 bulk head (I think it is) and had issues.
TIA

Still working on CT when I can
Joe Chisolm
Express CT builder
Marble Falls, Texas
jkturner
Posts: 6
Joined: Tue Jul 22, 2014 7:55 pm

Re: Static port location

Post by jkturner »

I recently upgraded my panel to include and all glass panel Skyview setup. I added 2 static ports behind the rear cabin bulkhead about 18". I have had no problems at all with this location. I can provide pictures if you would like.
jkturner
Posts: 6
Joined: Tue Jul 22, 2014 7:55 pm

Re: Static port location

Post by jkturner »

I recently upgraded my panel to all glass (Dynon Skyview) in my Express CT (N360EZ) and needed to add static ports because I would no longer be able to make use of the static port that was in the old pitot tube. I added to 2 new aluminum static ports that I purchased from AC Spruce. I put them on both sides of the fuselage behind the rear bulkhead access panel. I have had no issues with the system since making this change, all has worked out very well. Let me know if you would like pics and I would be glad to take some for you showing the installation.

Jeff Turner
209-495-3061
jeffreyhowell
Posts: 11
Joined: Mon Aug 15, 2016 2:56 pm

Re: Static port location

Post by jeffreyhowell »

Mine is located about 8 inches aft of the firewall and about 2/3 of the way up from the lower surface OML. I do not know how accurate it is going to be but static ports are easy to calibrate. In past experiences I have used a thin piece aluminum (to create a step) in front of the port or behind the port. The thickness of the step will influence your calibration. One other thing I have done is to buy a static port from AS and machine a step in it just behind the hole and then I clock the port when I screw it on so that I get an accurate reading.
jchisolm
Posts: 111
Joined: Tue Jun 17, 2014 9:56 pm

Re: Static port location

Post by jchisolm »

Thanks for the info. I've read elsewhere about doing a step like that.
Joe Chisolm
Express CT builder
Marble Falls, Texas
n49ex
Posts: 12
Joined: Tue Mar 14, 2017 2:49 pm

Re: Static port location

Post by n49ex »

I did have a pitot mast which included the static ports, and found that after adding the G3X Touch autopilot, the AP hunted vertically. evidently the pitot integrated static ports deliver slightly varying pressure with changes in AOA, not noticeable on the altimeter, but causing AP instability. As a result I have engaged in a massive effort to locate the best place for fuselage ports, starting out with a location about 18 inches back from the 162 bulkhead, and while the AP is stable, found the altitude and airspeed off. I've come up with a method of experimentally locating the optimum spot, without drilling numerous holes, and am in the process of writing a Kitplanes article on it. I think it turns out that relatively few homebuilders really know how accurate their airspeed and altitude are, or the laborious processes by which static ports are located on certified product. In any case, for the purpose of Express owners, I have determined that the best location (at least on my plane) is just ahead of the 162 bulkhead, which unfortunately for me is in the baggage door. Fortunately, locating the ports just behind the bulkhead is nearly as good - within 1 mph and 10 feet altitude, so that is what I have chosen as an acceptable compromise. I am using Cleveland Tool aluminum ports.

Incidentally, contrary to the beliefs of some others, I have found the addition of a step ahead of or behind the port hole as a compensation/correction mechanism to not be very effective except for small corrections. That is to say that if your ports are say, greater than 6" from the neutral pressure transition line, a step will not be able to adequately correct it. A 0.060" step will deliver only about a 20ft altitude correction, while altitude error is in the neighborhood of 6 to 7 feet per inch of lateral displacement in the neutral pressure area of the Express. Furthermore, with a step, the correction may not be compensating correctly over a range of speeds, as the boundary layer thickness changes.

Food for thought!

Reinhard Metz
Post Reply